Diy Display Case : How To Build Wood And Acrylic DIY Display Case

8 min read

diy display case

Diy display case – Yet an additional woodworking project, I made a decision making myself a wooden case for my HO locomotives and rolling supply. For several years I have actually maintained my automobiles closed in among those level cardboard boxes with foam cellular lining. This is an OKAY service however I constantly need to take out as well as put away the box whenever I wish to venture out the trains. Plus lacking a genuine format nobody could really ever actually see the vehicles I have.

Undoubtedly you have seen much of these cases, made of whatever from Cherry, Maple, Oak and also Pine. I determined to make my own from Maple. I particularly like how the grain looks and it’s an extremely hard timber and also conveniently makes a nice looking case. Plus I haven’t done much collaborate with Maple so I believed this would certainly be a wonderful possibility to try it out.

How to Build a Wood DIY Display Case

The key to knowing ways to build a timber case is in ensuring that clear glass is used in most, if not all, of the panels as well as doors. A fantastic wood display case need to do simply that, show exactly what is inside the case. An exceptional addition to mounting glass in a wood case is to mount effective illumination and also glass shelves. Both of these additions will make sure everybody can see exactly what gets on display in the wood case.

Required Materials for Safety

  • Safety glasses
  • Ear connects or headset
  • Handwear covers
  • Breathing mask

Specific Hardware for Glass

  • Tempered glass (see note below in write-up).
  • Takes care of.
  • Hinges.
  • Silicone adhesive.
  • Glass maintaining clips.
  • Magnetic locks.

Wood Hardware

  • Particle board screws.
  • Wood flathead screws.
  • Drill bits (especially for drilling pilot holes with bit board).
  • Adjustable shelf pins or rack strips with pins.
  • European hinges (optional).
  • Particle board.
  • Plywood (Oak).
  • Hardwood (Oak).
  • Table saw.
  • Biscuit joiner.
  • Biscuits, # 10 or # 20.
  • Mobile drill.
  • Establish of raised panel little bits (for door construction of door and also to house glass panels).
  • Router.

Step 1 – Building the Basic Wood DIY Display Case

Constructing the basic timber DIY display case could vary from an instead tiny square box that is around 12 inches broad, deep as well as tall, to a much larger, rectangle wall closet that is 31 inches broad by 12 inches deep by 80 inches high. The main difference between these cupboards as well as a wood display case will certainly be the enhancement of illumination, the glass panels and also racks.

An additional exceptional example of the best ways to build a timber display case is the construction of a darkness box. This is a standard square, measuring about 12 by 12 inches, and also about 6 inches deep. Products are installed inside this box, which is after that fitted with a glass-framed cover, just like an average image structure. The distinction is that rather than a photo, actual products are mounted within the image structure, creating a three-dimensional result.

Step 2 – Consideration of Glass Panels

As stated previously, the key to developing a timber display case is in the installment illumination, glass panels, shelves. When the cupboard is developed to whatever measurements are preferred, it is time to set up either toughened up or routine window glass. It is less costly to acquire normal window glass, cut it to the desired measurements and install it in the doors as well as cabinet panels.

It would be much more pricey to buy tempered glass, yet it is much more secure to use since in the event of it breaking, it shatters and will certainly protect against serious injuries. Tempered glass should be ordered to dimension due to the fact that unlike normal window glass, it can not be reduced at residence with a glass cutter.

Step 3 – Installation of Glass Panels, Shelves and Lighting

All that is required to install glass panels, racks and lights takes care consideration of equipment and setup treatments. Utilize the router and also a straight router bit to router a quarter inch groove around all the cupboard doors. Use a slim grain of silicone adhesive in between the groove and the set up glass panels. Safeguard the glass with either glass maintaining hardware or wood strips glued to the door or panel frames. Usage glass racks instead of timber, and set up a lighting fixture on top of the closet to brighten the closet.

How to Build an Acrylic DIY Display Case


Hi! I am going to show you ways to make an acrylic case. Its genuine simple and much cheaper compared to getting it custom-made by stores. You can pick the kinds, colours and also dimensions of acrylic sheets to create your situation to fit your taste. For this situation, I made it 30cm x 30cm x 350cm for the LEGO R2D2( isn’t it stunning!) with a mirrored aluminium-acrylic composite panel as the base. Let’s get started!


Diy display case. It was getting actually dirty but I did not really get into constructing a case for it then. You might have discovered that there is a display case next to it. That was my very first acrylic display case develop for my LEGO Volkswagen Camper Van. I did not share the construct it as it was not appropriately recorded. Anyways, back to the R2D2.

It was a dreadful quantity of dust accumulated and it did refrain from doing the R2D2 any kind of justice. It was time to obtain fracturing as well as make a display case for it.

Diy Display Case Design

I took the R2D2s measurements and also started attracting the style based on my previous design for the Volkswagen Camper Van. A 30cm x 30cm base sufficed to enable the R2D2 to be propped in various presents and also to accommodate the name plate. The R2D2 was gauged to be regarding 32cm. I then rounded this approximately 35 cm to offer it some headroom.

There are 7 panels in total; 5 Clear panels( Leading, A, B, C, D), 1 Black Panel( b) and also 1 mirrored panel( a). For the side panels, 2 of them need to be of a smaller sized width as they will be glued into the back of the broader panels. This is to make sure that package will certainly end up with equal sides. Given that the panels will certainly all have a density of 3mm, the two smaller panels would have to be 6mm less than the other 2 panels. The top will certainly after that be glued on the top with no excess on the sides. In my previous construct for the Volkswagen Camper Van, I needed to sand down the bottom panel a so about fit the cover. In this construct, I chose to obtain the bottom plate 1mm much less on each side. Below are the measurements I got:.

The adjustment in thickness for all-time low Panel a was due to that the firm I mosted likely to buy the acrylic only had the panel with a thickness for 4mm.

The illustration and dimensions for the design was really convenient when making my order and also purchasing the acrylic. I might refer as well as confirm for any type of blunders before placing in my order.

Diy Display Case : Materials Required :

  • Polymer Sheets: 7 panels in total; 5 Clear Panels, 1 Black Panel and also 1 Mirrored Panel.
  • Polymer Glue. From.
  • Syringe with needle. From Guardian.
  • Clamps. The one left wing was from Daiso. The various other was from Homefix.
  • Wood Blocks( note that a person edge is chamfered).
  • Paper (to secure your job surface area).

I acquired my acrylic panels from DAMA Trading Pte Ltd. Each panel sets you back about SGD2-3 with the exemption of the aluminium-acrylic compound which costs SGD7. The panels came reduced to size. There was no completing or smoothing done to it yet were nevertheless still wonderful, straight cuts. Thus far DAMA has actually been my to-go look for acrylics for its range and also most importantly low cost.

Rather than using the syringe with needle to apply the glue, you could likewise use a brush to apply the acrylic glue. I am making use of the capillary action to allow the glue to leak into the joint, therefore the syringe with needle. The syringe and also needles could be found in personal wellness and care stores such as Watsons or Guardian. They are reasonably low-cost. I can not remember how much though. I obtained the glue from [email protected] Besah.

I obtained the clamp on the left from Daiso, where everything goes to SGD2, a few years back. I can not seem to discover it stocked there anymore. They are great clamps for their cost. The one left wing was from Home-Fix. It cost me under SGD10. I can not remember the specific cost though.

From SGD2. The wooden block functions as assistance for the panels when they are being glued. The chamfered side of the block prevents the adhesive from can be found in call with the block as well as bonding. This left quite a nasty little bit of timber stuck onto the panel in my last build. I used my Dremel to make the chamfer. If you do not have a Dremel, you could merely use a saw to just merely cut off the edge. The idea is making it chamfered sufficient to stop it from being available in contact with the joint.

Diy Display Case – Assembly

First, you will have to prepare your acrylic panels by getting rid of the component of the safety layer on the edge you will certainly be gluing. Keep the remainder of it on to secure it from square one. You could trim off the overhanging peeled safety layer with a pair of scissors if it enters your way. I started with the 350mm x 300mm panel first.
Next off, prop up the 350mm x 294mm panel with the wood blocks as well as clamp onto the panel. Remember to peel of the protective layer as pointed out for the first item, however on both sides. Take note that i have my 350mm x 300mm panel on the bottom as well as the 350mm x 294mm panel ahead.

Change the clamp as well as block to make certain the panels are in proper call with each other. Check that the panels are lined up appropriately prior to applying the glue. I loaded the syringe with the glue. You do not have to pack up the entire syringe. About 2ml will certainly be ample.

To apply the glue, just rest the needle on the joint and also press the syringe to expel the glue while running the needle along the sign up with. The glue will certainly permeate into the joint making use of capillary action. It is alright if you make a spill. The adhesive will evaporate away. The most awful thing you might do is smear it and make a mess. It will take around 2 hrs for the adhesive to bond, however i want to leave it over night to allow the glue to sit perfectly. Do the same for the opposite. Make sure you obtain the proper panel prior to gluing it on.

When you obtained 3 sides done, the 4th side will certainly be a little problematic. Flip the assembly such that the lower panel now encounters up and also put it on the Fourth panel. You may notice that the sides might not be straightened. Yet that is alright. Glue one edge initially, seeing to it the other side goes to least hing on the panel to ensure that there is also call and sustain it with the blocks and clamps.

As soon as that is done, do the very same for the other side. For this side, it might tend to escape when you try to straighten it. I positioned some books on the top to use some pressure onto the panel as well as used some Blue Tack to stop the block from sliding away. It functioned well and also was able to maintain the panel from removaling while the adhesive bound.
Using books as weights. Exactly what else could they be used for?

As soon as that is done, we can adhesive the leading panel. Peel and removed the protective layer on the edges.

Prepare the side panel setting up by peeling off and also cutting off the protective layer on the brink to be glued. Aim to utilize the side you locate is one of the most flushed to be glued to the top panel.

Lay the side panel assembly onto the leading panel and straighten them. There may be some minor imbalance. Attempt to get the best positioning. Apply adhesive. When the adhesive sets, you could peel away all the protective layers and also marvel at your work so far.

For the last part, just join the two base plates with each other. I used double-sided tape since i could not utilize the exact same glue on it given that the aluminium-acrylic composite panel has a steel base as well as I felt that the double-sided tape would certainly be adequate. Do a check by laying both lower plates together then placing the constructed cover. The cover needs to rest nicely under panel and also not move around too much. If you feel that you have to decrease the panel size to enable the cover to rest better, do so in the past gluing the lower panels together.

Prepare your products inside the case and you are done!

Diy Display Case : Conclusion

Diy display case. This is an actually easy and beneficial develop if you have products you intend to show and secure from dirt. You could select different colours such as various colour colors or a various base plate. By using the exact same setting up method, you could also create extra complex designs such as a light-up system. Purchasing a similar case from shops will typically cost you at the very least SGD60. I did all this with no greater than SGD25 and also little work.

Leave a Reply

Your email address will not be published. Required fields are marked *